original 3-star review:
seems to work well in all respects apart from the touch function. yes, i removed the protective film and, yes, both 5v inputs are powered.
i have email'd the mfg - resolution pends...
UPDATE: Sun Jan 19 16:19:33 EST 2020
OK... it works. my bad - connection issue. on receiving an email from the mfg/cust support, i was advised to "please connect to Pi3B+ as the attached manual".
tl;dr
i'm using an R Pi 3B+ with OpenAuto running on Raspbian and i intend to mount it in an '04 ford ranger.
the "quick start guide" is not terribly useful. less than useful, actually, and there is no other documentation.
the display is bright, crisp and clear, and the touch function works quite well. read on for full disclosure.
the unabridged version:
as mentioned, the enclosed directions aren't all that great. under the 3 line paragraph marked "to use it as a touch screen for the R Pi, you may need:". here, it shows a picture of the enclosed FPC cable with the caption, "an fpc cable, to connect your R Pi to this touch screen". in their defense, there is another pic of a Pi (only) with 3 cables attached, with a caption, "to use it as a standard monitor..." wherein it indicates 3 cables are required including a note to connect the "5V+ Touch" to "your connected device".
off to youtube. i found a review of the lebula display on the first search, but is was completely useless. quite by accident, i discovered another video (https://www.youtube.com/watch?v=_HUt6tRReEQ) for the UPerfect display but it appears to be exactly the same as this touch screen.
in case the link is redacted, the video may be found at the standard youtube url with the id "v=_HUt6tRReEQ".
unfortunately for most readers here, it's in german, but it is visually very clear and the german-impaired (myself included) may simply view a few spots in the video for the complete info:
connection of rpi connections to display starts at 8:30
closeup of almost complete wiring at 9:30
complete wiring at 9:45
its made by EddyD's SmartHome. Danke für das Video, EddyD.
note that this video shows a connection scheme using an included cable (there are several) marked, "gift- 3pin power cable for the R Pi" and a very short micro-usb-to-usb-A cable. and, of course, the FPC cable. if you're not familiar with one or more of these, watch more of the video.
eureka.
size info - useful if you have a place in mind to mount it:
actual screen dimensions (excluding mounting tabs): 4.2 x 6.5 inches, diagonally: 7.7
overall dimension: 6.5 x 4.75
4 mounting tabs which extend the height by 0.375 each.
thickness with R Pi attached: ~1.25"
the indicated resolution is 1024 x 600 but the description on the amazon page says it supports 1280 x 1024. there is no mention of this in the quick start guide.
it comes with a 5v 3a power brick (approx 2" x 1.6" x 1") which may be a switching PS as it does not get very warm, at least after approx 30 min use.
under actual operation it uses approx 0.9a at 5.1v (approx 4 and a half watts). it did hit 1.2a very briefly during boot. my Pi displayed the "lightning bolt" using the above described connection arrangement - it may require it's own power supply.
the warranty (as advertised on the QSG):
30 day return
60 day replacement
12 mo warranty
24 hr cust svc via email
life-time after sale service
summary and conclusions:
i've had the display power'd up for only an hour or so, so i can't speak to reliability, but it behaves as advertised - bright, clear, responsive, apparently well built. there are several cables which are included eg., hdmi-hdmi, usb-micro-usb, FPC. there are adjustments for brightness, contrast, color temp, etc.
i have no idea if the power brick will behave above 1 amp, but it behaved well for my purposes. i will be powering it using the DROK 90483 8A 100W DC Car Power Supply (amazon page https://smile.amazon.com/gp/product/B00C4QVTNU/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1).
unless i have issues in the near future, i plan to purchase at least 2 more units.
the pic is a capture from the vid - hope you don't mind EddyD. :-)
Enjoy fast, free delivery, exclusive deals, and award-winning movies & TV shows with Prime
Try Prime
and start saving today with fast, free delivery
Consider a similar item
$69.00
Climate Pledge Friendly
Add a debit or credit card to save time when you check out
Convenient and secure with 2 clicks. Add your card
Make it a bundle
We found 4 bundles with this item:
ROADOM Raspberry Pi Screen, 10.1’’ Touchscreen Monitor, IPS FHD 1024×600,Responsive and Smooth Touch,Dual Built-in Speakers,HDMI Input,Compatible with Raspberry Pi 5/4/3/Zero,Easy Assembly,Driver Free
Page 1 of 1Start overPage 1 of 1
-
ROADOM 10.1'' Raspberry Pi Monitor & 10.1'' Touchscreen with Case$186.99 $209.98This bundle contains 2 items -
ROADOM 10.1'' Raspberry Pi Monitor & 7'' Touchscreen with Case$166.99 $189.98This bundle contains 2 items
Frequently bought together
$99.99
Get it as soon as Friday, May 17
In Stock
+
Total price:
To see our price, add these items to your cart.
Choose items to buy together.
Similar items that may deliver to you quickly
Page 1 of 1 Start overPage 1 of 1
Videos
Page 1 of 1Start OverPage 1 of 1
Videos for this product
0:18
Click to play video
7in IPS Touch Screen for Raspberry Pi Projects
It’s All About The Build
Videos for this product
0:19
Click to play video
Customer Review: Great Customer Service - DOA Unit Replaced Fast
Joey S.
Videos for this product
0:18
Click to play video
Customer Review: Customer support is great
Albert Calef
Product Description
|
|
|
|
|---|---|---|
IPS 178° Full Viewing Angle PanelCompared to other TN panels, this IPS touchscreen monitor comes with 178° full viewing angle, offering excellent image and video performance even you are not viewing this small monitor from the front. Tips: Long-Time viewing this 10 inch monitor from other angles is not recommended, since it's not good for your eyesight after all. |
HD ResolutionFeaturing with 1024*600 HD resolution, ROADOM Raspberry Pi screen delivers top notch picture and full color display. 1024*600 is a perfectly suitable resolution for many GUI applications! Tips: Some Raspberry Pi will boot to resolution like 640x480 without any modification. However, if you want this Raspberry Pi monitor to offer 1024x600 you would still need to modify the config.txt in raspbian boot directory. |
Versatile Ports, Plug and PlayROADOM Raspberry Pi touchscreen comes with 2 microUSB ports, the upper one for Power, the other one for Touch, and HDMI port for Signal. Besides, there are another 3 ports on the back, which are used for gift cables. You can easily mount your Raspberry Pi directly on the back of this Raspberry Pi display with gift cables completely hidden, providing a clean interface and cable management. |
How to connect to Raspberry Pi with gift cables? (Raspberry Pi 4 Model B is shown as an example.)
Raspberry Pi can be directly mounted to the back of this touchscreen monitor with the gift cables completely hidden, helping a lot with reducing clutter and making a neat wire connection.
ROADOM 10.1 inch hdmi monitor works great for other various applications! This is a great touch screen monitor for hobbyists of all levels.
FAQ
Q1: My Raspbian doesn't have built-in support for the monitor's native 1024x600 pixels, how should I configure the native 1024x600 pixel resolution?
A: You can modify /boot/config.txt as shown below to configure the native 1024x600 pixel resolution:
framebuffer_width=1024
framebuffer_height=600
hdmi_force_hotplug=1
hdmi_cvt=1024 600 60 3 0 0 0
hdmi_group=2
hdmi_mode=87
Save the file and reboot and you should be running at the native resolution.
Q2: Does the package include any case for this 10.1'' monitor?
A: No, please kindly write to us for specific dimensions of this touchscreen monitor if you want to make the case yourself.
Q3: Does this 10.1'' Raspberry Pi screen need any driver?
A: No, plug and play.
Q4: If the monitor gets power from Raspberry Pi, will 5V/2A power adapter be enough?
A: No, please use the 5V/3A power adapter included in the package. The monitor may flicker when getting insufficient or unstable power supply.
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|
| 10.1 Inch Touchscreen Monitor | 7 Inch Touchscreen Monitor | 10.1 Inch Touchscreen with Case | 7 Inch Touchscreen with Case | 4K Ultra HD Portable Monitor | 4.7-17.3'' Tablet Stand | |
| Customer Reviews |
1,159
|
1,159
|
89
|
89
|
79
|
249
|
| Price | $99.99 | $79.99 | $109.99 | $89.99 | $219.99 | $26.59 |
| Resolution | 1024*600 | 1024*600 | 1024*600 | 1024*600 | 3840*2160 | / |
| Response Time | 3-5 ms | 3-5 ms | 3-5 ms | 3-5 ms | / | / |
| Panel Type | IPS Full Viewing Angle | IPS Full Viewing Angle | IPS Full Viewing Angle | IPS Full Viewing Angle | IPS Full Viewing Angle | / |
| Aspect Ratio | 16:9 | 16:9 | 16:9 | 16:9 | 16:9 | / |
| Contrast | 700:1 | 700:1 | 700:1 | 700:1 | 1500:1 | / |
| Size | 9.2 x 5.6 x 0.3 inch | 6.5x4.8x0.5 inch | 9.71 * 6.05 * 7.81 inch | 6.95 * 4.35 * 6.12 inch | 14.5 * 8.8 * 0.3 inch | 6.3 * 6.3 * 11 inch |
| Weight | 439g | 237g | 1.23 lb | 0.78 lb | 1.7 lb | 1.65 lb |
| Brightness | 300cd/m² | 300cd/m² | 300cd/m² | 300cd/m² | 500cd/m² | / |
| Refresh Rate | 60Hz | 60Hz | 60Hz | 60Hz | 60Hz | / |
From the brand
ROADOM Monitors
Focus on Your Visual and Auditory Enjoyment!
-
Featuring with high and new technology, ROADOM keeps designing and manufacturing top-quality electronic products such as portable monitors, Raspberry Pi screens, CD players, Tablet Stands etc., offering excellent usage experience for customers all over the world.
We stands behind all ROADOM products.
If any questions about any product, please feel free to come to us.
-
-
-
Enhance Game Experience
-
Expand Your Phone Screen
Compare with similar items
This Item  ROADOM Raspberry Pi Screen, 10.1’’ Touchscreen Monitor, IPS FHD 1024×600,Responsive and Smooth Touch,Dual Built-in Speakers,HDMI Input,Compatible with Raspberry Pi 5/4/3/Zero,Easy Assembly,Driver Free |  |  |  |  |  | |
| Price | $99.99 | $109.99 | -5% $71.59 Typical: $74.99 | $75.99 | -7% $79.99 Typical: $85.99 | $84.59 |
| Delivery | Get it as soon as Friday, May 17 | Get it as soon as Friday, May 17 | — | Get it as soon as Friday, May 17 | Get it as soon as Friday, May 17 | Get it as soon as Friday, May 17 |
| Customer Ratings | ||||||
| Touch Screen | ||||||
| Value for money | ||||||
| Screen quality | ||||||
| Picture quality | ||||||
| Sold By | ROADOM-US | ROADOM-US | iPistBit | HONGXINBAORUI | Hengmiao Official Store | iPistBit |
| display size | 10.1 inches | 10.1 inches | — | 10.1 inches | 10.1 inches | 10.1 inches |
| resolution | SVGA Wide | SVGA Wide | SVGA Wide | HD | HD | HD |
| display technology | LCD | LCD | LCD | LCD | LCD IPS Display | LCD |
| hardware interface | hdmi, usb2.0 micro a | hdmi, usb c, 3 5 mm audio | — | hdmi | hdmi, usb2.0 | usb, hdmi |
| viewing angle | 178 degrees | 178 degrees | 178 degrees | 178 degrees | 178 degrees | 178 degrees |
| mounting type | Desk/Wall Mount | Desk Mount | — | Ceiling | Bracket Mount | Wall Mount |
| HDMI ports | 1 | — | — | 1 | 1 | 1 |
Reviews with images
DOA - With Updates...
Ordered this as a proof of concept for a marine plotter. On paper the specs would be ok. Enough to beta test.Unit arrived with the ribbon connector soldered on backwards. Unable to insert, and too short to make the reach to the HDMI port on the RPi4.Hooking up with regular HDMI port and usb-a for power and touch results in a dead screen. Sending back for refund.**Update** - Customer support was wonderful in addressing the matter. Screen was defective, new replacement arrived in less than 48 hours. New screen turns on and connects as advertised. The touch functionality is not configured properly on my Raspberry Pi, so thats a software issue, but otherwise, it appears to be functioning quite well. No 5 stars due to the whole issue, but 4 is a big jump from 1...
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Reviewed in the United States on January 15, 2020
seems to work well in all respects apart from the touch function. yes, i removed the protective film and, yes, both 5v inputs are powered.
i have email'd the mfg - resolution pends...
UPDATE: Sun Jan 19 16:19:33 EST 2020
OK... it works. my bad - connection issue. on receiving an email from the mfg/cust support, i was advised to "please connect to Pi3B+ as the attached manual".
tl;dr
i'm using an R Pi 3B+ with OpenAuto running on Raspbian and i intend to mount it in an '04 ford ranger.
the "quick start guide" is not terribly useful. less than useful, actually, and there is no other documentation.
the display is bright, crisp and clear, and the touch function works quite well. read on for full disclosure.
the unabridged version:
as mentioned, the enclosed directions aren't all that great. under the 3 line paragraph marked "to use it as a touch screen for the R Pi, you may need:". here, it shows a picture of the enclosed FPC cable with the caption, "an fpc cable, to connect your R Pi to this touch screen". in their defense, there is another pic of a Pi (only) with 3 cables attached, with a caption, "to use it as a standard monitor..." wherein it indicates 3 cables are required including a note to connect the "5V+ Touch" to "your connected device".
off to youtube. i found a review of the lebula display on the first search, but is was completely useless. quite by accident, i discovered another video (https://www.youtube.com/watch?v=_HUt6tRReEQ) for the UPerfect display but it appears to be exactly the same as this touch screen.
in case the link is redacted, the video may be found at the standard youtube url with the id "v=_HUt6tRReEQ".
unfortunately for most readers here, it's in german, but it is visually very clear and the german-impaired (myself included) may simply view a few spots in the video for the complete info:
connection of rpi connections to display starts at 8:30
closeup of almost complete wiring at 9:30
complete wiring at 9:45
its made by EddyD's SmartHome. Danke für das Video, EddyD.
note that this video shows a connection scheme using an included cable (there are several) marked, "gift- 3pin power cable for the R Pi" and a very short micro-usb-to-usb-A cable. and, of course, the FPC cable. if you're not familiar with one or more of these, watch more of the video.
eureka.
size info - useful if you have a place in mind to mount it:
actual screen dimensions (excluding mounting tabs): 4.2 x 6.5 inches, diagonally: 7.7
overall dimension: 6.5 x 4.75
4 mounting tabs which extend the height by 0.375 each.
thickness with R Pi attached: ~1.25"
the indicated resolution is 1024 x 600 but the description on the amazon page says it supports 1280 x 1024. there is no mention of this in the quick start guide.
it comes with a 5v 3a power brick (approx 2" x 1.6" x 1") which may be a switching PS as it does not get very warm, at least after approx 30 min use.
under actual operation it uses approx 0.9a at 5.1v (approx 4 and a half watts). it did hit 1.2a very briefly during boot. my Pi displayed the "lightning bolt" using the above described connection arrangement - it may require it's own power supply.
the warranty (as advertised on the QSG):
30 day return
60 day replacement
12 mo warranty
24 hr cust svc via email
life-time after sale service
summary and conclusions:
i've had the display power'd up for only an hour or so, so i can't speak to reliability, but it behaves as advertised - bright, clear, responsive, apparently well built. there are several cables which are included eg., hdmi-hdmi, usb-micro-usb, FPC. there are adjustments for brightness, contrast, color temp, etc.
i have no idea if the power brick will behave above 1 amp, but it behaved well for my purposes. i will be powering it using the DROK 90483 8A 100W DC Car Power Supply (amazon page https://smile.amazon.com/gp/product/B00C4QVTNU/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1).
unless i have issues in the near future, i plan to purchase at least 2 more units.
the pic is a capture from the vid - hope you don't mind EddyD. :-)
Size: 7 InchVerified Purchase
touch function does not work - resolution pends... RESOLVED
Reviewed in the United States on January 15, 2020
original 3-star review:Reviewed in the United States on January 15, 2020
seems to work well in all respects apart from the touch function. yes, i removed the protective film and, yes, both 5v inputs are powered.
i have email'd the mfg - resolution pends...
UPDATE: Sun Jan 19 16:19:33 EST 2020
OK... it works. my bad - connection issue. on receiving an email from the mfg/cust support, i was advised to "please connect to Pi3B+ as the attached manual".
tl;dr
i'm using an R Pi 3B+ with OpenAuto running on Raspbian and i intend to mount it in an '04 ford ranger.
the "quick start guide" is not terribly useful. less than useful, actually, and there is no other documentation.
the display is bright, crisp and clear, and the touch function works quite well. read on for full disclosure.
the unabridged version:
as mentioned, the enclosed directions aren't all that great. under the 3 line paragraph marked "to use it as a touch screen for the R Pi, you may need:". here, it shows a picture of the enclosed FPC cable with the caption, "an fpc cable, to connect your R Pi to this touch screen". in their defense, there is another pic of a Pi (only) with 3 cables attached, with a caption, "to use it as a standard monitor..." wherein it indicates 3 cables are required including a note to connect the "5V+ Touch" to "your connected device".
off to youtube. i found a review of the lebula display on the first search, but is was completely useless. quite by accident, i discovered another video (https://www.youtube.com/watch?v=_HUt6tRReEQ) for the UPerfect display but it appears to be exactly the same as this touch screen.
in case the link is redacted, the video may be found at the standard youtube url with the id "v=_HUt6tRReEQ".
unfortunately for most readers here, it's in german, but it is visually very clear and the german-impaired (myself included) may simply view a few spots in the video for the complete info:
connection of rpi connections to display starts at 8:30
closeup of almost complete wiring at 9:30
complete wiring at 9:45
its made by EddyD's SmartHome. Danke für das Video, EddyD.
note that this video shows a connection scheme using an included cable (there are several) marked, "gift- 3pin power cable for the R Pi" and a very short micro-usb-to-usb-A cable. and, of course, the FPC cable. if you're not familiar with one or more of these, watch more of the video.
eureka.
size info - useful if you have a place in mind to mount it:
actual screen dimensions (excluding mounting tabs): 4.2 x 6.5 inches, diagonally: 7.7
overall dimension: 6.5 x 4.75
4 mounting tabs which extend the height by 0.375 each.
thickness with R Pi attached: ~1.25"
the indicated resolution is 1024 x 600 but the description on the amazon page says it supports 1280 x 1024. there is no mention of this in the quick start guide.
it comes with a 5v 3a power brick (approx 2" x 1.6" x 1") which may be a switching PS as it does not get very warm, at least after approx 30 min use.
under actual operation it uses approx 0.9a at 5.1v (approx 4 and a half watts). it did hit 1.2a very briefly during boot. my Pi displayed the "lightning bolt" using the above described connection arrangement - it may require it's own power supply.
the warranty (as advertised on the QSG):
30 day return
60 day replacement
12 mo warranty
24 hr cust svc via email
life-time after sale service
summary and conclusions:
i've had the display power'd up for only an hour or so, so i can't speak to reliability, but it behaves as advertised - bright, clear, responsive, apparently well built. there are several cables which are included eg., hdmi-hdmi, usb-micro-usb, FPC. there are adjustments for brightness, contrast, color temp, etc.
i have no idea if the power brick will behave above 1 amp, but it behaved well for my purposes. i will be powering it using the DROK 90483 8A 100W DC Car Power Supply (amazon page https://smile.amazon.com/gp/product/B00C4QVTNU/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1).
unless i have issues in the near future, i plan to purchase at least 2 more units.
the pic is a capture from the vid - hope you don't mind EddyD. :-)
Images in this review
Reviewed in the United States on March 23, 2023
Size: 10.1 InchVerified Purchase
This screen is great for its price! Easy to use, big screen, bright vibrant colors. Screen FPS is smooth, and what I really loved was that it included tons of additional cables/attachments and even a stylus. I got a ribbon cable, HDMI, HDMI mini, USB, and pretty much any other adapter you could imagine. I also attached this to my PC (windows) via HDMI, and it works great! No worries, no additional setup is needed! I have tried quite few other screens before for my raspberry pi 4 (wavshare and sunny) and they seem to be a lot more fragile and harder to use, but this is a great alternative. Compared to other brands, this screen feels a lot more robust, and contains much more tools and accessories, making it a great value for money. I was also able to contact their customer support, and they seem to reply very quick (within 15 mins of contact). I would definitely recommend this screen to others looking to find a reliable touchscreen for their computer/tablet/raspberry pi. Only thing I would like to have found is a housing, so I can package the screen and raspberry pi together in one.
Images in this review
